Goulds 3196 Pump Specifications-manufacture,factory,supplier from China

1. The 3196 ANSI Series is available in a wide range of sizes, capacities and materials to fit virtually any process-fluid application.

Proven PerformanceOver One Million Process Pump Installations WorldwideWhen the 3196 ANSI Standard Dimension Process Pump was first introduced in 1961, it immediately became the standard for the industry. Today, the number of installations attest to its remarkable performance.

Fast and accurate impeller setting with the industry's most innovative external impeller adjustment mechanism.In-shop reverse vane impeller adjustment with the only pump that takes full advantage of the back pull-out design.BEARING INSTALLATION FOR POWER END ASSEMBLY (CONT'D)Both bearings have a slight interference fit which requires that they be pressed on the shaft with an arbor or hydraulic press. A chart giving bearing fits is shown in Figure 35. Even force should be applied to the inner race only. Never press on the outer race, as the force will damage the balls and races.

The 3196 ansi series is to be had in a huge range of sizes and capacities to match clearly any method-fluid software.Utility: Chemical processingGeneral industriesMiningWater sourcesEnergy technologyPrimary metalsPulp and paperOil and gasolineCapacities to 7000 GPM (1590 m³ /h)Heads to 730 feet (223 m)Temperatures to 700° F (371° C)Pressures to 375 PSIG (26 bar)Available Size:6''-15''Part NameMaterialDuctile Iron316SSCD4MCuAlloy 20NickelHastelloy CTitaniumCasing316SSCD4MCuAlloy 20NickelHastelloy CTitaniumImpeller316SSCD4MCuAlloy 20NickelHastelloy CTitaniumCover316SSCD4MCuA

Centrifugal Pump. • Model 3196. • S/N 788B861. • Size 1 in. x1-1/2 in. x 8 in. • Water flush double mechanical seals. Motor 1.5 hp, 1,730 rpm, 230/460 V, 60 Hz, 5.6/2,8 amps, 3 phase, Capacity 14 gpm. • Overall Dimensions 35 in. L x 12 in. W x 15 in.

Proven PerformanceEvery day in over 500,000 installations, the 3196 ASME/ANSI (B73.1M) process pump proves why it’s the industry standard for performance.

Product DescriptionProven PerformanceUsers in chemical, petrochemical, pulp & paper, primary metals, food & beverage and general industries know they can make no better choice than the best -  Model 3196.Power Ends are the result of over 160 years of design experience, customer interaction, and continuous improvement.  Customers get extended MTBF (Mean Time Between Failure) and lower LCC (Life Cycle Cost)….guaranteed!

Safety•  ANSI B15.1 coupling protect•  Ductile iron body adapterFirst rate capabilities for top notch performanceProlonged pump existenceEase of protection•  Lower back pull-out layout•  External impeller adjustment•  Most interchangeabilityMost fulfilling hydraulic performance•  Absolutely open impeller•  Complete 50/60 hz coverage•  29 sizes•  automatic pump choiceThe 3196 ANSI Series is available in a wide range of sizes, capacities and materials to fit virtually any process-fluid application.Part NameMaterialDuctile Iron316SSCD4MCuAlloy 20Nickel

The 3196 ANSI Series is recognized international as the most suitable name in ANSI chemical method pumps. And it is available in a extensive variety of sizes, capacities and materials to meet any application requirements.1.Application:Chemical ProcessingGeneral IndustriesMiningWater ResourcesPower GenerationPrimary MetalsPulp and PaperOil and Gas2.Capacities to 7000 GPM (1590 m³ /h)Heads to 730 feet (223 m)Temperatures to 700° F (371° C)Pressures to 375 PSIG (26 bar) 3.Available Size:6''-15''

When the 3196 ANSI Pump was first introduced in 1961, it immediately became the standard in the industry.  Today, the number of installations attest to its remarkable performance.  Users in chemical, petrochemical, pulp & paper, primary metals, food & beverage and general industries know they can make no better choice than the best.1. Application: Chemical ProcessingGeneral IndustriesMiningWater ResourcesPower GenerationPrimary MetalsPulp and PaperOil and Gas2.Capacities to 7000 GPM (1590 m³ /h)Heads to 730 feet (223 m)Temperatures to 700° F (371° C)Pressures to 375

DESIGN FEATURESFully Open ImpellerEngineered Seal ChambersPatented Taperbore™ PLUS Seal ChamberBigBore™ Seal Chambersi-FRAME Power EndsOnboard Condition MonitoringInpro VBXX-D Hybrid Bearing IsolatorsOptimized Sump DesignPremium Severe Duty Thrust BearingsLTi Power End for High Load ApplicationsEngineered Pump Mounting SystemsEase of MaintenanceBack Pull-out DesignExternal Impeller AdjustmentMaximum InterchangeabilityOptional C-Face Motor AdapterOptimum Hydraulic PerformanceFull 50/60 Hz Coverage29 SizesSafetyHeavy Duty CasingsHydrostatic Testing of All Pressure Retaining ComponentsANSI B15.1

Every day in over 500,000 installations, 3196 ASME/ANSI (B73.1M) process pump proves why it’s the industry standard for performance.

Chemical Process PumpsDesigned for Total Range ofIndustry ServicesI Capacities to 7000 GPM (1364 m 3 /h)I Heads to 730 feet (223 m)I Temperatures to 700°F (371° C)I Pressures to 375 PSIG (2586 kPa)Product Description:The 3196 ANSI series is to be had in a huge variety of sizes, capacities and materials to match virtually any system-fluid utility.ImpellerDesigned for long-term, maintainable performance and minimum hydraulic loads formaximum reliability.CASING• Top centerline discharge for air handling, self-venting.• Class 150 pumps have Class 300 wall thickness as standard.• Back pull-out desi

Fully open impeller is the best design for the chemical process industries services. Ideally suited for corrosives and abrasives, handles solids and stringy fibers with ease. Allows for simple restoration of clearances when wear takes place.

The 3196 ANSI Series is available in a extensive variety of sizes, capacities and materials to match sincerely any manner-fluid software. Capacities to 7000 GPM (1590 m³ /h) Heads to 730 feet (223 m) Temperatures to 700° F (371° C) Pressures to 375 PSIG (26 bar)1.Application: Chemical ProcessingGeneral IndustriesMiningWater ResourcesPower GenerationPrimary MetalsPulp and PaperOil and Gas2.Available Size:6’’-15’’3.Part NameMaterialDuctile Iron316SSCD4MCuAlloy 20NickelHastelloy CTitaniumCasing316SSCD4MCuAlloy 20NickelHastelloy CTitaniumImpeller316SSCD4MCuAlloy 20NickelHa

BASEPLATE INSPECTION1. Remove all equipment.2. Completely clean the underside of baseplate. It is sometimes necessary to coat the underside of the baseplate with an epoxy primer. This may have been purchased as an option.3.

3196 takes fully open impeller which is the best design for the chemical process industries services. Ideally suited for corrosives and abrasives, handles solids and stringy fibers with ease.

The 3196 ANSI collection is to be had in a wide variety of sizes, capacities and substances to match absolutely any technique-fluid application.RECEIVING THE PUMPInspect the pump as soon as it is received. Carefully check that everything is in good order. Make notes of damaged or missing items on the receipt and freight bill. File any claims with the transportation company as soon as possible.STORAGE REQUIREMENTSShort Term: (Less than 6 months) normal packaging procedure is designed to protect the pump during shipping.

The 3196 ANSI Series is available in a extensive variety of sizes, capacities and materials to match sincerely any manner-fluid software.1.Application:  Chemical ProcessingGeneral IndustriesMiningWater ResourcesPower GenerationPrimary MetalsPulp and PaperOil and Gas 2.Capacities to 7000 GPM (1590 m³ /h)Heads to 730 feet (223 m)Temperatures to 700° F (371° C)Pressures to 375 PSIG (26 bar)  3.Available Size:6’’-15’’ 4.ImpellerDesigned for long-term, maintainable performance and minimum hydraulic loads formaximum reliability. CASING• Top centerline discharge for air

The ahlstar product line offers a extensive variety of hydraulic sizes to guarantee minimal power intake. Pump hydraulics, casings and impellers are designed to optimize fluid handling abilties. shares are pumped like water. debris in sludges do no longer collect inside the pump, or slurries are efficaciously channeled in order not to cause wear.The back vanes of the impeller keep  the area between the impeller and the  casing cover clean, and reduce the  axial load on the bearings.

1.Our pump broadly used for all conventional pumping event in pulp and paper mills. the precise design of app pump, make the pumping slurry easy like water, slurry density can attain 8%.2.Overall performance(max parameter)Heads 160mCapability 2000l/sTemperature 180℃3.To be had size:32-600

Reliable OperationHigh Efficiency Wide Hydraulic CoverageBetween bearings, unmarried level, axially cut up, double access appropriate for fashionable business pumping in addition to low pulsation headbox packages in ppi with notably polished inner surfaces.Overall performance varietySulzer pumps gives correct coverage with many pump sizes for low and high head applications with high efficienciePerformance  Capacity max.

Our Pump substitute components are reliable, cost effective replacement elements which might be interchangeable with durco etc widely known pump manufacturers.We manufacture more than a few substitute parts including shafts, casings, impellers, stuffing container covers, sleeves, labyrinth seals, repellers, backplates, fans and plenty of more.MAINTENANCEPREVENTIVE MAINTENANCEA procedure for keeping accurate maintenance records is a critical part of any program to improve pump reliability. There are many variables that can contribute to pump failures.

The product line offers a wide range of hydraulic sizes to guarantee minimum power consumption. Pump hydraulics, casings and impellers are designed to optimize fluid handling capabilities. Stocks are pumped like water. Particles in sludges do not accumulate in the pump, or slurries are effectively channeled so as not to cause wear.The back vanes of the impeller keep the area between the impeller and the casing cover clean, and reduce the axial load on the bearings.Balance holes in the impeller are used to stabilize the pressure in the seal chamber.