ZPP Pump-manufacture,factory,supplier from China

Huge hydraulic coverage1.our slurry tank flushing pump especially design for cutting-edge high-tempo paper tool, board gadget and moreover very relevant for different big potential pumping event.2.overall performance(max parameter)Heads 130mAbility 6500l/s  temperature a hundred and twenty℃

ANSI Mark III 4x3-10H bare shaft pump in WCB material, other materials like CD4M, CF8M, A20 etc are all available. And our pumps are 100% interchangeble with leading enterprise's one.If any needs, pls contact me for quotation.

We are at Pump&Fluid Euipment Exhibition

Our chemical process pump provides outstanding hydraulic performance, unrivaled reliability and low total cost of ownership.

 The working principle of the engine water pump: Through the belt pulley to drive the pump bearing and the impeller to rotate, the cooling liquid in the pump is driven by the impeller to rotate together, and is thrown to the edge of the pump shell under the effect of Centrifugal Force, at the same time generating certain pressure, and then it comes out of a drain or a pipe.

Besides casting pump parts and maching pump parts, we also supply gasket, bearing, O-ring, oil seal etc accessories for assembling a pump.Pls let me know if any needs, I'd like to offer you for your reference.

This kind of pump is used for all normal pumping applications, with stocks up to 8%, e.g., liquors, water, chemicals, white water, condensate, etc.Capacities 11,000 m³/h / 48,400 USgpmHeads 160 m / 525 ftPressures 16 / 25 bar, 230 / 360 psi,depending on material and sizeTemperatures 180 °C / 356 °FPls let me know if you have any needs.

Car water pump is an critical element to keep the normal working temperature of the engine. after the water pump is broken, it'll purpose many problems, the most critical of if you want to lead to engine damage. the subsequent section summarizes the performance of water pump failure, which is helpful to get rid of engine failure quicker and shield the automobile.The faults of the pump are as follows: (1) Unstable idle speed: the fault of the pump will lead to the increase of the rotation resistance of the pump.

The hydraulic design of two-phase flow pulp pump adopts the principle of “Relative suction and relative blocking”in the theory of two-phase flow, so that the hydraulic performance of the flow parts of the pump conforms to the law of solid-liquid two-phase flow, thus reducing the slurry flow parts of the erosion and wear, greatly improving the efficiency and service life of the pump, the pump series has the following notable features:1.High efficiency and energy saving: The running efficiency is 3-10 percentage points higher than the average of the ordinary pulp pump, the energy saving and cons

PerformanceHead up to 110 m. Temperature max. 180 °C. Capacity up to 2000 l/s. Operating frequencies 50 or 60 Hz. Pressure up to 1.6 MPa, depending on material and size.

Operating Parameters• Flows to 4540 m3/h (20 000 US gpm) • Heads to 215 m (700 ft) • Pressures to 27 bar (400 psi) • Temperatures from -73°C (-100°F) to 370°C (700°F) • Discharge sizes from 25 mm (1 in) to 200 (8 in)  The material of wet ends like A20, CD4M, 316SS, Titanium, Hastelloy C, Nickel etc are all available, if any needs, I'd like to offer you for your reference.

First. Classification by impeller number 1. Single-stage pump: that is, there is only one impeller on the pump shaft. 2. Multi-stage pump: that is, there are two or more impellers on the pump shaft, and the total lift of the pump is the sum of the lifts generated by n impellers. Second, classified according to work pressure 1. Low-pressure pump: the pressure is less than 100m H2O; 2. Medium pressure pump: the pressure is between 100 and 650 meters of water column; 3.